Halloween Special Sale 75% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: sale75best

Free Cisco 300-710 Practice Exam with Questions & Answers | Set: 5

Questions 41

An engineer is deploying Cisco Secure Endpoint for the first time and on endpoint with MAC address 50:54:15:04:0:AB. The engineer must make sure that during the testing phase no files are isolated and network connections must not be blocked. Which policy type must be configured to accomplish the task?

Options:
A.

Triage

B.

Quarantine

C.

Protect

D.

Audit

Cisco 300-710 Premium Access
Questions 42

A company is deploying intrusion protection on multiple Cisco FTD appliances managed by Cisco FMC. Which system-provided policy must be selected if speed and detection are priorities?

Options:
A.

Connectivity Over Security

B.

Security Over Connectivity

C.

Maximum Detection

D.

Balanced Security and Connectivity

Questions 43

An engineer is configuring a Cisco Secure Firewall Threat Defence device managed by Cisco Secure Firewall Management Centre. The device must have SSH enabled and the accessible from the inside interface for remote administration. Which type of policy must the engineer configure to accomplish this?

Options:
A.

Identify

B.

Access control

C.

Prefilter

D.

Platform settings

Questions 44

An engineer is configuring a multidomain instance of Cisco Secure Firewall Management Center. The instance must be integrated with Cisco Secure Endpoint. What must the engineer configure to allow multiple domains to have hosts with the same IP-MAC address pairs?

Options:
A.

second-level domain

B.

leaf domain

C.

global domain

D.

subdomain

Questions 45

Which Cisco Firepower rule action displays an HTTP warning page?

Options:
A.

Monitor

B.

Block

C.

Interactive Block

D.

Allow with Warning

Questions 46

An administrator configures a Cisco Secure Firewall Threat Defense device in transparent mode. To configure the BVI (Bridge Virtual Interface), the administrator must:

Add a bridge-group interface

Configure a bridge-group ID

Configure the bridge-group interface description

Add bridge-group member interfaces

How must the engineer perform these actions?

Options:
A.

Configure a name for the bridge-group interface

B.

Set a security zone for the bridge-group interface

C.

Set the bridge-group interface mode to transparent

D.

Configure an IP address for the bridge-group interface

Questions 47

What is needed to start a threat investigation in Cisco XDR?

Options:
A.

indicator of compromise

B.

local IP address

C.

user name

D.

indicator of attack

Questions 48

Which firewall design will allow It to forward traffic at layers 2 and 3 for the same subnet?

Options:
A.

Cisco Firepower Threat Defense mode

B.

routed mode

C.

Integrated routing and bridging

D.

transparent mode

Questions 49

An engineer is troubleshooting application failures through a FTD deployment. While using the FMC CLI. it has been determined that the traffic in question is not matching the desired policy. What should be done to correct this?

Options:
A.

Use the system support firewall-engine-debug command to determine which rules the traffic matchingand modify the rule accordingly

B.

Use the system support application-identification-debug command to determine which rules the traffic matching and modify the rule accordingly

C.

Use the system support firewall-engine-dump-user-f density-data command to change the policy and allow the application through the firewall.

D.

Use the system support network-options command to fine tune the policy.

Questions 50

A security engineer is adding three Cisco FTD devices to a Cisco FMC. Two of the devices have successfully registered to the Cisco FMC. The device that is unable to register is located behind a router that translates all outbound traffic to the router ' s WAN IP address. Which two steps are required for this device to register to the Cisco FMC? (Choose two.)

Options:
A.

Reconfigure the Cisco FMC lo use the device ' s private IP address instead of the WAN address.

B.

Configure a NAT ID on both the Cisco FMC and the device.

C.

Add the port number being used for PAT on the router to the device ' s IP address in the Cisco FMC.

D.

Reconfigure the Cisco FMC to use the device ' s hostname instead of IP address.

E.

Remove the IP address defined for the device in the Cisco FMC.

Exam Code: 300-710
Certification Provider: Cisco
Exam Name: Securing Networks with Cisco Firepower (300-710 SNCF) v1.2
Last Update: Nov 3, 2026
Questions: 444

Cisco Related Exams

How to pass Cisco 300-715 - Implementing and Configuring Cisco Identity Services Engine (SISE) v1.1 (300-715 SISE) Exam
How to pass Cisco 350-701 - Implementing and Operating Cisco Security Core Technologies (SCOR 350-701 v2.0) Exam
How to pass Cisco 300-740 - Designing and Implementing Secure Cloud Access for Users and Endpoints Exam
How to pass Cisco 300-745 - Designing Cisco Security Infrastructure Exam
700-826 - Cisco IoT Essentials for Account Managers (IOTAM)
700-821 - Cisco IoT Essentials for System Engineers (IOTSE)
810-115 - Cisco OT Security Practitioner
500-443 - Advanced Administration and Reporting of Contact Center Enterprise (CCEAAR)
300-615 - Troubleshooting Cisco Data Center Infrastructure
300-215 - Conducting Forensic Analysis and Incident Response Using Cisco CyberOps Technologies (CBRFIR v1.2)
200-201 - Understanding Cisco Cybersecurity Operations Fundamentals
300-815 - Implementing Cisco Advanced Call Control On-Premises
CCST-Networking - Cisco Certified Support Technician (CCST) Networking Exam
300-220 - Conducting Threat Hunting and Defending using Cisco Technologies for Cybersecurity
300-540 - Designing and Implementing Cisco Service Provider Cloud Network Infrastructure
Cisco Free Access
Get Cisco Full Access

Cisco Free Exams
Cisco Free Exams
Examstrack offers free Cisco exam materials and practice tests to aid your Cisco certification journey.