Free CWNP CWDP-305 Practice Exam with Questions & Answers | Set: 2

Software-defined radios (SDRs) offer flexibility in RF operation. In dual-band APs, an SDR can be programmed to operate on either 2.4 GHz or 5 GHz, allowing dynamic optimization of the spectrum based on demand and interference.

From CWDP-305:

“Software-defined radios can be configured to operate in either band, allowing administrators to shift coverage based on band congestion or capacity requirements.”

This flexibility helps address issues in high-density deployments or when minimizing interference is critical.

— Reference: CWDP-305 Official Study and Reference Guide, Chapter on Infrastructure Design

Comprehensive and Detailed Explanation:

Mounting APs above the ceiling can significantly degrade WLAN performance due to signal attenuation caused by ceiling materials and obstructions. If aesthetic requirements were not communicated during the initial requirements gathering, the current deployment does not align with the documented design specifications. The appropriate course of action is to inform the stakeholder that the WLAN performance requirements may not be met under the current installation and that a new design process is necessary to address the aesthetic constraints while ensuring optimal performance.

Manual identification of radar pulses using spectrum analysis charts can be challenging because radar signals often have low amplitude at the Wi-Fi receiver, making them difficult to detect visually.This limitation can lead to inaccurate assessments of DFS channel availability.Automated detection methods or using the actual WLAN equipment intended for deployment may provide more reliable results.

Comprehensive and Detailed Explanation:

Real-Time Location Systems (RTLS) utilize various technologies to track and locate assets or individuals in real-time. The methods include:

A. Sound:Ultrasonic sensors can be used for location tracking by measuring the time it takes for sound waves to travel between devices.

B. 802.11-capable laptops:Wi-Fi-based RTLS can leverage existing 802.11 infrastructure and devices to determine location based on signal strength and triangulation.

C. Active RFID:Active RFID tags have their own power source and can transmit signals to readers, allowing for real-time tracking over longer distances.

D. Infrared:Infrared sensors can be used for location tracking, especially in environments where line-of-sight is available.

F. UWB (Ultra-Wideband):UWB technology provides high-precision location tracking by transmitting signals over a wide frequency spectrum.

G. Passive RFID:Passive RFID tags do not have their own power source and are activated by the electromagnetic field of a reader, suitable for tracking items in close proximity.

E. UHV:Ultra-High Voltage (UHV) is not a technology used in RTLS and is therefore not applicable.

Active site surveys involve connecting to the WLAN and measuring performance metrics such as signal strength, throughput, and roaming behavior.This type of survey is essential to verify that clients can seamlessly roam between APs without connectivity issues.

The CWDP-305 Official Study and Reference Guide highlights the role of active surveys in assessing the real-world performance of a WLAN, including the effectiveness of roaming configurations.

When calculating the total noise figure of cascaded components, Friis' formula is used:

F_total = F1 + (F2 - 1)/G1 + (F3 - 1)/(G1 × G2) + ...

Where:

F_totalis the total noise factor (linear, not in dB).

F1, F2, ...are the noise factors of the individual stages.

G1, G2, ...are the gains of the preceding stages (linear, not in dB).

In this scenario, the amplifier has a gain of 0 dB, which corresponds to a linear gain of 1. A noise figure of 10 dB corresponds to a noise factor of 10. Assuming the cable and filter have negligible noise contributions or are passive components with minimal loss, their impact on the total noise figure is minimal.

Applying Friis' formula:

F_total = 10 + (1 - 1)/1 = 10

Converting back to dB:

NF_total = 10 × log10(10) = 10 dB

When working at heights, especially during the installation of Access Points (APs) on high ceilings, safety is paramount.Personal Protective Equipment (PPE) such as hardhats protect against head injuries, high visibility vests ensure that workers are easily seen, and body belts (or harnesses) provide fall protection.These are standard safety measures in such environments.NWExam

The CWDP-305 Official Study and Reference Guide underscores the importance of appropriate PPE:

"Ensure that installation personnel use appropriate PPE, including hardhats, high visibility vests, and body belts, when working at heights."

This issue arises due to partial support for 5 GHz channels by some client devices. Although the infrastructure may use all 25 available 5 GHz channels in the U.S. (spanning UNII-1 through UNII-3 and DFS channels), many older 802.11n tablets and clients only support a subset of these channels—commonly the lower UNII-1 band (channels 36–48). As a result, even though the APs are operational and signal coverage is valid overall, the client may not see or associate with APs operating on unsupported 5 GHz channels such as channels 52–64 or DFS channels (100–144).

This leads to inconsistent connectivity or lack of signal in areas where APs are broadcasting on unsupported channels. The CWDP-305 Study Guide advises taking client capability into account during design validation and includes best practices for mapping expected device support versus operational channel plans.

Comprehensive and Detailed Explanation:

IEEE 802.3at, also known as PoE+, provides up to 30 watts of power per port. To calculate the minimum Power over Ethernet (PoE) budget required for 6 access points (APs):

30 W/AP × 6 APs = 180 W

Therefore, a switch must have a minimum PoE budget of180 wattsto support six 802.3at-powered APs.

Comprehensive and Detailed Explanation:

In predictive modeling for WLAN design:

B.Setting the AP transmit power to match the average client device capabilities (e.g., 25 mW) ensures a balanced link budget, promoting reliable two-way communication and accurate coverage predictions.

A.While default antenna patterns can be used, they may not accurately represent the actual deployment, especially if different antennas are planned.

C.Channel width settings should reflect the intended deployment plan, which may include 20 MHz, 40 MHz, or 80 MHz channels, depending on the environment and requirements.

D.Using pre-configured vendor-specific AP and antenna models in the predictive software ensures that thesimul-ationclosely matches the actual hardware characteristics, leading to more accurate predictions.