Free Cisco 300-615 Practice Exam with Questions & Answers | Set: 2

Configure the Filter field with sAMAccountName=$company is the appropriate UCS remediation because the symptom maps to a specific managed object rather than a generic server failure. Cisco UCS abstracts hardware through service profiles and policies; therefore, issues involving UCS, UCS Manager, LDAP must be corrected where UCS Manager programs the adapter, boot target, firmware, management certificate, pool qualification, or fabric interconnect state. The selected answer restores that programming path. The other options may appear plausible, but they do not correct the object that UCS uses to derive operational state. For example, boot failures require the correct vHBA/iSCSI target and LUN policy, discovery issues require the proper physical and management path, and firmware failures require the documented recovery action for the failed FSM stage. The correct validation is to inspect the associated fault, confirm inventory acknowledgment, verify the policy under the service profile or equipment tree, and then recheck boot or connectivity behavior after the FSM completes.

The selected answer, Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs, follows Cisco UCS operational logic. UCS Manager is policy-driven, so troubleshooting must determine whether the problem is caused by hardware discovery, service profile association, firmware activation, boot order, storage presentation, or management integration. The scenario points to service profile, vNIC; that is why the selected action fixes the root condition rather than merely restarting the server. The wrong options either affect a different policy, require unnecessary disruption, or assume that physical connectivity alone is sufficient. Cisco documentation for UCS server boot and firmware management stresses that boot policies must include the correct target details, firmware workflows must complete their FSM stages, and hardware changes often require acknowledgement or re-acknowledgement before UCS Manager uses the new inventory. After remediation, the engineer should confirm that the UCS fault is cleared, the server association or discovery state is complete, and the operating system or management service can use the intended path.

The selected answer, Reset the faulty module from the peer IOM, follows Cisco UCS operational logic. UCS Manager is policy-driven, so troubleshooting must determine whether the problem is caused by hardware discovery, service profile association, firmware activation, boot order, storage presentation, or management integration. The scenario points to UCS, UCS Manager, firmware, Auto Install, IOM; that is why the selected action fixes the root condition rather than merely restarting the server. The wrong options either affect a different policy, require unnecessary disruption, or assume that physical connectivity alone is sufficient. Cisco documentation for UCS server boot and firmware management stresses that boot policies must include the correct target details, firmware workflows must complete their FSM stages, and hardware changes often require acknowledgement or re-acknowledgement before UCS Manager uses the new inventory. After remediation, the engineer should confirm that the UCS fault is cleared, the server association or discovery state is complete, and the operating system or management service can use the intended path.

The selected option, Add the event -default action statement to the end of the script, is correct for the automation path described. Cisco NX-OS requires precision in EEM applets, scheduler jobs, Guest Shell operations, and REST/NX-API syntax. The affected element is EEM, SNMP; therefore, the fix must be applied to the component that actually executes the action. For EEM, that means a valid event detector and explicit actions, with event-default when the matched CLI command should continue. For Guest Shell and Bash, DNS, proxy, resource allocation, and reboot behavior are local to the Linux container. For REST calls, the class name, method, authentication, and XML/JSON structure must match the APIC or NX-OS object model. The distractors usually change the switch globally or alter an unrelated command. Cisco DCIT automation troubleshooting confirms the fix by checking the returned error, then rerunning the exact job, script, or API operation in the same context.

The ports that connect the FEX to the fabric interconnects must be configured as server ports is correct because the failure is tied to the UCS managed state of FEX, UCS, UCS Manager, fabric interconnect, Cisco Nexus. In Cisco UCS, policies are not advisory; they are the source from which fabric interconnects program adapters, boot targets, server identity, firmware, and external integrations. A mismatch between the policy and the actual hardware or upstream storage/network state can cause boot, discovery, KVM, firmware, or connectivity failures. The selected action addresses the object that UCS Manager uses to build the final operational configuration. The distractors either solve a different fault domain or bypass the policy model. A disciplined DCIT validation sequence is to check the fault code, the FSM history, the equipment inventory, the service profile association, and the relevant adapter or boot table. If those states are correct after the change, the UCS component should return to operable service without unnecessary reconfiguration.

Include a new VLAN on the appliance port is the correct fix under Cisco SAN troubleshooting practice. The issue described involves UCS, vNIC, vHBA, where the operating state depends on the correct combination of port type, VSAN, fabric service, and access-control database. MDS and Nexus SAN features do not infer missing policy: if the active zoneset, fabric-binding database, fcdomain, NPIV setting, or FCoE/LLDP negotiation is wrong, the link may come up physically but the initiator will not reach the target. The selected answer corrects the missing or mismatched element. The remaining choices either act at the wrong layer, change a non-causal parameter, or provide only a temporary reset. After applying the fix, a proper Cisco validation path is to review show interface, show flogi database, show fcns database, show zoneset active, and any isolation or merge-failure logs. That confirms the storage network is operationally consistent.

The selected answer, 1. Connect Fabric Interconnect B and execute “Erase configuration” 2. Reboot Fabric Interconnect B. 3. Add the subordinate Fabric Interconnect to the cluster, follows Cisco UCS operational logic. UCS Manager is policy-driven, so troubleshooting must determine whether the problem is caused by hardware discovery, service profile association, firmware activation, boot order, storage presentation, or management integration. The scenario points to fabric interconnect; that is why the selected action fixes the root condition rather than merely restarting the server. The wrong options either affect a different policy, require unnecessary disruption, or assume that physical connectivity alone is sufficient. Cisco documentation for UCS server boot and firmware management stresses that boot policies must include the correct target details, firmware workflows must complete their FSM stages, and hardware changes often require acknowledgement or re-acknowledgement before UCS Manager uses the new inventory. After remediation, the engineer should confirm that the UCS fault is cleared, the server association or discovery state is complete, and the operating system or management service can use the intended path.

Issue permit distribute on core-2 is the correct fix under Cisco SAN troubleshooting practice. The issue described involves VSAN, Cisco Nexus, Nexus 9000, Cisco Nexus 9000, where the operating state depends on the correct combination of port type, VSAN, fabric service, and access-control database. MDS and Nexus SAN features do not infer missing policy: if the active zoneset, fabric-binding database, fcdomain, NPIV setting, or FCoE/LLDP negotiation is wrong, the link may come up physically but the initiator will not reach the target. The selected answer corrects the missing or mismatched element. The remaining choices either act at the wrong layer, change a non-causal parameter, or provide only a temporary reset. After applying the fix, a proper Cisco validation path is to review show interface, show flogi database, show fcns database, show zoneset active, and any isolation or merge-failure logs. That confirms the storage network is operationally consistent.

Assign an MP-BGP AS number to the fabric; Specify the spine nodes as route reflectors is the valid corrective action because the failure described is a protocol or fabric state problem, not a generic connectivity issue. For BGP, ACI, Cisco troubleshooting expects the engineer to compare both endpoints of the relationship: vPC peers must agree on consistency parameters, HSRP peers must exchange hellos in the same VLAN and version context, OSPF/BGP peers must match the attributes required for stable adjacency, and VXLAN EVPN must advertise the correct host or prefix information. The selected option restores that required state. The other options either operate on the wrong layer, change a value that is not used to form the relationship, or would make the peer relationship less deterministic. A clean validation is to inspect the control-plane table first, then verify the forwarding table, and finally test end-to-end traffic. This is the Cisco-preferred approach because it avoids random changes and confirms that the fabric is forwarding based on correct protocol state.

Enable the NPIV mode on the Cisco Nexus 5000 switch is the correct fix under Cisco SAN troubleshooting practice. The issue described involves VSAN, NPIV, NPV, Cisco Nexus, where the operating state depends on the correct combination of port type, VSAN, fabric service, and access-control database. MDS and Nexus SAN features do not infer missing policy: if the active zoneset, fabric-binding database, fcdomain, NPIV setting, or FCoE/LLDP negotiation is wrong, the link may come up physically but the initiator will not reach the target. The selected answer corrects the missing or mismatched element. The remaining choices either act at the wrong layer, change a non-causal parameter, or provide only a temporary reset. After applying the fix, a proper Cisco validation path is to review show interface, show flogi database, show fcns database, show zoneset active, and any isolation or merge-failure logs. That confirms the storage network is operationally consistent.