Free Exin CDCP Practice Exam with Questions & Answers | Set: 3

According to the CDCP Preparation Guide1, risk can be defined as the product of impact and probability. Impact is the measure of the negative consequences or losses that may result from a risk event, such as downtime, data loss, or damage to the data centre. Probability is the measure of the likelihood or frequency of a risk event occurring, based on historical data, expert judgment, or statistical analysis. By multiplying impact and probability, risk can be quantified and compared, which helps in prioritizing and mitigating the risks. For example, a risk event that has a high impact but a low probability may have the same risk level as a risk event that has a low impact but a high probability.

According to the EPI Data Centre Training Framework, lithium-ion batteries are becoming more popular in data centres due to their higher energy density, longer lifespan, and lower maintenance costs compared to lead-acid batteries1. However, lithium-ion batteries also have some drawbacks, such as higher initial cost, stricter safety requirements, and potential thermal runaway risks1. Therefore, a battery management system (BMS) is essential to monitor and control the voltage, current, temperature, and state of charge of each battery cell or module, and to prevent overcharging, over-discharging, or overheating23. A BMS can also communicate with the UPS system and provide information on the battery status, performance, and health2.

The most damaging type of floor load for raised floor tiles in a data centre is the rolling load (RL), according to the CDCP Preparation Guide1 and various web sources234. A rolling load is the load that is applied by a moving object, such as a pallet jack, a forklift, or a rack on wheels. A rolling load can cause more stress and fatigue on the raised floor tiles than a static load, such as a concentrated load (CP) or a uniformly distributed load (UDL), because it creates dynamic forces and impacts that can crack, dent, or deform the tiles. Moreover, a rolling load can also damage the pedestals and stringers that support the tiles, and cause the tiles to become loose or misaligned. Therefore, when designing and installing a raised floor system, it is important to consider the maximum rolling load that the tiles can withstand, and to use appropriate materials and methods to enhance the strength and durability of the tiles. For example, some possible solutions include using steel or concrete-filled tiles, reinforcing the edges and corners of the tiles, and using locking or gravity-held systems to secure the tiles.

Direct air handlers are a type of cooling system that use outdoor air to cool the data centre. They draw in fresh air from outside, filter it, and supply it to the data centre at the desired temperature and humidity level. Direct air handlers can reduce the energy consumption and operating costs of data centres by eliminating the need for mechanical cooling or refrigeration. However, they also have some challenges and limitations that need to be considered. One of the main factors to consider when using direct air handlers for data centres is the temperature, humidity and contamination of the outdoor environment. Depending on the location and climate of the data centre, the outdoor air may not always be suitable for cooling the data centre. For example, if the outdoor air is too hot, too humid, or too polluted, it may not provide enough cooling capacity, or it may damage the IT equipment or cause corrosion. Therefore, direct air handlers need to have sensors and controls to monitor the outdoor air quality and adjust the airflow accordingly. They may also need to have backup cooling systems or supplementary cooling devices, such as evaporative coolers or heat exchangers, to cope with extreme weather conditions or peak loads.

The four main components of a refrigeration circuit are the evaporator, the compressor, the condenser, and the expansion valve, according to the CDCP Preparation Guide1 and various web sources234. A refrigeration circuit is a system that transfers heat from a low-temperature region to a high-temperature region, using a working fluid called refrigerant. The refrigeration circuit operates in a closed loop, where the refrigerant changes its state from liquid to vapor and back to liquid, while absorbing and releasing heat. The four main components of the refrigeration circuit perform the following functions:

•The evaporator is a heat exchanger that absorbs heat from the low-temperature region, such as the data centre room, and transfers it to the refrigerant. The refrigerant enters the evaporator as a low-pressure, low-temperature liquid, and leaves the evaporator as a low-pressure, low-temperature vapor.

•The compressor is a mechanical device that increases the pressure and temperature of the refrigerant vapor. The refrigerant enters the compressor as a low-pressure, low-temperature vapor, and leaves the compressor as a high-pressure, high-temperature vapor.

•The condenser is another heat exchanger that releases heat from the refrigerant to the high-temperature region, such as the outside air or water. The refrigerant enters the condenser as a high-pressure, high-temperature vapor, and leaves the condenser as a high-pressure, low-temperature liquid.

•The expansion valve is a device that reduces the pressure and temperature of the refrigerant liquid. The refrigerant enters the expansion valve as a high-pressure, low-temperature liquid, and leaves the expansion valve as a low-pressure, low-temperature liquid. The expansion valve also controls the flow of the refrigerant into the evaporator, depending on the cooling load.

Shielded twisted pair cables (STP) are Ethernet cables that feature additional protection against electromagnetic interference from external sources, such as radio waves, microwaves, or other network cables. This is achieved by wrapping each pair of wires with a conductive shield, usually made of foil or braided wire, and then enclosing the entire cable with another shield layer. However, this shielding is not effective against low frequency electromagnetic fields (EMF) from power cables, which can induce currents and voltages in the network cables and cause signal distortion or data loss. Low frequency EMF can only be reduced by increasing the distance between the power and network cables, or by using a tre-foil cable arrangement, which is a special configuration of three power cables twisted together to cancel out the magnetic fields they generate.