Master the CompTIA A+ Certification Exam: Core 1 220-1101 Exam with Confidence!

In this situation, the best course of action for the technician to take NEXT would be C. Verify the socket type and manufacturer. If the pins on the CPU do not line up with the socket on the motherboard, it is likely that there is a compatibility issue between the two components. The technician should verify that the socket type and manufacturer of the motherboard match those of the CPU to ensure that they are compatible.

According to the CompTIA A+ Core 1 (220-1101) Certification Study Guide1, a network crimper and a cable stripper are the tools that a technician should use to resolve this issue. A network crimper is used to attach a new RJ-45 connector to the end of the cable, and a cable stripper is used to remove the outer insulation of the cable and expose the twisted pairs of wires. A toner probe, a punchdown tool, a multimeter, and a loopback plug are not needed for this task.

Here are some web resources that explain how to repair an Ethernet cable:

• Ethernet Cable Repair - iFixit: This guide provides step-by-step instructions and pictures on how to fix a broken Ethernet cable.
• How to Repair a Cut Cat5e Ethernet Cable - wikiHow: This article shows how to solder the wires of a cut Ethernet cable and use shrink tube to cover the joints.
• Amazon.com: Ethernet Cable Repair Kit: This page lists some products that can be used to repair an Ethernet cable, such as crimping tools, connectors, testers, and strippers.

The correct answer is D. Raise the filament flow amount.

Filament flow amount, also known as extrusion multiplier or flow rate, is the setting that controls how much filament is extruded by the nozzle during 3D printing. It is usually expressed as a percentage of the default value, which is 100%. Increasing the filament flow amount means extruding more filament than usual, while decreasing it means extruding less1.

The filament flow amount can affect the quality and adhesion of the first layer, which is crucial for a successful 3D print. If the filament flow amount is too low, the nozzle may not extrude enough filament to fill the gaps between the lines and create a smooth and solid first layer. This can result in poor adhesion, curling, warping, or detachment of the print from the bed12.

To improve adherence on the first layer, the user should raise the filament flow amount slightly, such as 105% or 110%, to ensure that enough filament is extruded to create a strong bond with the bed. The user should also make sure that the nozzle height, bed leveling, and bed temperature are properly calibrated for optimal first layer adhesion12.

The other options are less likely to improve adherence on the first layer, because:

•Lowering the print bed temperature may reduce the adhesion of the TPU filament to the bed, as TPU usually requires a bed temperature between 20-60°C for the best results3. Lowering the bed temperature may also increase the risk of warping or curling of the print4.

•Adjusting the RPM of the cooling fan may not have a significant effect on the first layer adhesion, as cooling fans are not required with TPU3. In fact, using a cooling fan with TPU may cause cracking or delamination of the print, as TPU needs to cool down slowly and evenly4.

•Increasing the print speed may worsen the first layer adhesion, as TPU is a flexible and elastic filament that needs to be printed slowly and consistently. A recommended print speed for TPU is 15-30mm/s3. Increasing the print speed may cause clogging, stringing, blobs, or under-extrusion of the filament4.

For more information and tips on how to 3D print TPU filament like a pro, you can visit these links:

•How to 3D Print TPU Filament Like a Pro – Ultimate Guide & FAQ

•The Complete TPU Filament 3D Printing Guide - 3DSourced

•TPU Filament 3D Printing Material – The Complete Guide

•TPU filament - learn everything about the TPU material for 3D printing

The correct answer is D. Cat 6a.

Cat 6a (augmented) is a type of twisted pair cable that supports 10GBASE-T data transmission speed. 10GBASE-T is an Ethernet standard that can deliver 10 gigabits per second (Gbps) over copper cables. Cat 6a can support this speed up to a distance of 100 meters, which is the same as Cat 5e and Cat 6 for lower speeds. Cat 6a has better shielding and crosstalk prevention than Cat 6, which makes it more suitable for high-frequency signals.

Cat 3, Cat 5, and Cat 5e are not capable of supporting 10GBASE-T data transmission speed. Cat 3 can only support up to 10 Mbps, Cat 5 can only support up to 100 Mbps, and Cat 5e can only support up to 1 Gbps. These cables have lower bandwidth, higher attenuation, and more interference than Cat 6a.

A captive portal is a web page that requires users to agree to terms and conditions, enter credentials, or provide payment information before accessing a wireless network. Some devices, such as streaming media devices, may not have a web browser or a user interface to interact with the captive portal. One possible solution is to connect to the hotspot on the user’s device, such as a smartphone or a tablet, and use it as a bridge to access the internet through the wireless network. The user’s device can authenticate with the captive portal and share its internet connection with other devices via Wi-Fi, Bluetooth, or USB. Reference: https://partners.comptia.org/docs/default-source/resources/a-core-1-content-guide (page 12)

A community cloud model is a cloud solution in which infrastructure is shared among organizations that have common interests, goals, or concerns, such as security, compliance, or industry standards. This model would best address the bank’s need to leverage cloud computing while maintaining a high level of security and privacy for its data and transactions. The other cloud models are not suitable for this scenario, as they either do not offer enough control over the infrastructure (public cloud), or do not allow for sharing of resources among similar organizations (private cloud and hybrid cloud). Verified References: [What Is Community Cloud?]

The correct answer is B. Check the power supply wattage rating.

A possible cause of the desktop randomly shutting down during operations is that the power supply is not able to provide enough power for the high-end graphics card. The power consumption of today’s graphics cards has increased a lot, and the top models demand between 110 and 270 watts from the power supply1. Therefore, the technician should check the power supply wattage rating and make sure it is sufficient for the graphics card and the rest of the components. Confirming the power supply is grounded, checking whether the power supply is redundant, or confirming the power cables are well connected are not likely to solve this problem.

Two-factor authentication (2FA) is a method of verifying a user’s identity by requiring two pieces of evidence: something the user knows (such as a password) and something the user has (such as a device). A mobile authenticator application is a software program that runs on a smartphone or tablet and generates a one-time code or token that the user can enter along with their password to access a system. This adds an extra layer of security to prevent unauthorized access.

References

•The Official CompTIA A+ Core 1 Student Guide (Exam 220-1101), page 13-14

•CompTIA A+ Certification Exam Core 1 Objectives, page 9, objective 2.5

•What is Two-Factor Authentication?

A scope is a term used to define a range of IP addresses available to assign using DHCP. DHCP stands for Dynamic Host Configuration Protocol, and it is a protocol that automatically assigns IP addresses and other network configuration parameters to devices on a network. A scope defines the start and end IP addresses, as well as other options, such as subnet mask, default gateway, and DNS servers.

The correct answer is A. Access point.

An access point is a device that extends the wireless coverage of a network by creating a hotspot that allows wireless devices to connect to the network1. An access point can be connected to a router or a switch via an Ethernet cable or a wireless bridge1. By deploying one or more access points throughout a SOHO location, the technician can provide better wireless connectivity and eliminate dead zones or weak signals2.

A managed switch is a device that allows multiple devices to communicate on a network by forwarding data packets based on their destination addresses3. A managed switch can also provide advanced features such as VLANs, QoS, security, and remote management3. However, a managed switch does not improve wireless connectivity, as it only works with wired devices.

A POE hub is a device that provides power and data over a single Ethernet cable to devices that support Power over Ethernet (PoE) technology, such as IP cameras, VoIP phones, and wireless access points4. A POE hub can simplify the installation and placement of these devices by eliminating the need for separate power adapters or outlets4. However, a POE hub does not improve wireless connectivity by itself, as it still requires an access point or a router to create a wireless network.

A Wi-Fi router is a device that combines the functions of a router and an access point, providing both wired and wireless connectivity to a network and the internet. A Wi-Fi router can be used to create a SOHO network, but it may not be sufficient to cover the entire location with a strong and reliable wireless signal. To improve wireless connectivity, the technician may need to add additional access points or use a mesh Wi-Fi system that consists of multiple routers that work together to create a seamless wireless network.

Therefore, an access point is the best option among the choices to improve wireless connectivity throughout a SOHO location.

The best way to connect the devices is A. Enable pairing.

Pairing is a process that allows two Bluetooth devices, such as a smartphone and a headset, to communicate with each other wirelessly. Pairing creates a secure connection between the devices and allows them to exchange data and audio signals. To pair the devices, the user needs to enable Bluetooth on both devices, make them discoverable, and select the desired device from the list of available devices. The user may also need to enter a PIN code or confirm a passkey to complete the pairing process .

The other options are not the best ways to connect the devices. A hotspot is a feature that allows a smartphone to share its cellular data connection with other devices via Wi-Fi, Bluetooth, or USB. A hotspot can provide internet access to other devices, but it does not allow them to communicate with each other directly. NFC stands for Near Field Communication, which is a technology that allows two devices to exchange data by bringing them close together (usually within 4 cm). NFC can be used to initiate pairing between two Bluetooth devices, but it cannot establish a connection by itself. Synchronization is a process that allows two devices to update and match their data, such as contacts, calendars, photos, or music. Synchronization can be done via Wi-Fi, Bluetooth, USB, or cloud services, but it requires an existing connection between the devices.

One of the benefits of virtualization is that it allows you to create and manage multiple virtual machines (VMs) on a single physical computer. This can be used to enhance security by centralizing all user desktops on a server, rather than storing them on individual user machines. This way, the user desktops can be isolated from each other and from the host machine, preventing malware infections, data breaches, and unauthorized access. Additionally, the user desktops can be easily backed up, restored, updated, and monitored by the administrator, reducing the risk of data loss and downtime.

This type of virtualization is called desktop virtualization, and it separates the desktop environment from the physical hardware the user interacts with1. The user can access their virtual desktop from any device, such as a laptop, tablet, or smartphone, using a remote display protocol. The user experience is similar to using a local desktop, but with improved security and manageability.

References:

•What Is Virtualization, and Why Should You Use it?, section “Desktop Virtualization”.

The correct answer is A. DHCP scope.

A DHCP scope is a consecutive range of IP addresses that a DHCP server can select from to fulfill requests from network clients. A DHCP server is a device that automatically assigns IP addresses and other network configuration parameters to devices that request them. A DHCP scope defines the pool of available IP addresses, as well as the subnet mask, default gateway, DNS servers, and lease duration for each IP address. A DHCP scope can also include exclusions, reservations, and policies to customize the IP address allocation process12.

A static IP list is a list of IP addresses that are manually assigned to devices and do not change over time. A static IP list does not require a DHCP server, but it requires more administrative effort and coordination to avoid conflicts or errors. A static IP list is not a consecutive range of IP addresses that a server can select from3.

DNS A records are DNS records that map a domain name to an IPv4 address. DNS is a system that translates human-readable domain names into machine-readable IP addresses. DNS A records are not a range of IP addresses that a server can select from, but a way of resolving domain names to IP addresses.

Automatic private IP addressing (APIPA) is a feature of Windows that allows devices to self-assign an IP address in the absence of a DHCP server or a static IP configuration. APIPA uses the 169.254.0.0/16 address range, which is reserved for link-local communication. APIPA does not create a range of IP addresses that a server can select from, but a fallback mechanism for devices that cannot obtain an IP address from another source.

For more information about DHCP scopes and other related topics, you can refer to the following web search results: DHCP Scope - NETWORK ENCYCLOPEDIA, Managing Microsoft DHCP Scope and other Components - ATA Learning, Dynamic Host Configuration Protocol (DHCP) | Microsoft Learn.

A thermal receipt printer uses heat to print on thermal paper, which has a special coating that reacts to heat and produces black marks. If the paper roll is inserted in the wrong orientation, the printer will not be able to print anything on the paper. Therefore, the first thing the technician should do is to check if the paper roll is loaded correctly, with the paper feeding under, not over. This is a common and easy mistake to fix, and it does not require any software or hardware changes.

References

•Troubleshooting Your Thermal Printer Problems - Thermal POS Receipt Printer Tips & Tricks, paragraph 2

•POS Thermal Receipt Printer Troubleshoot - Not Printing Evenly, video at 0:15

•Receipt Printer Troubleshooting – Shopfront, bullet point 2

The correct answer is A. Tethering.

Tethering is the process of sharing a mobile device’s internet data connection with other devices, such as laptops, tablets, or other phones. Tethering can be done by using a Wi-Fi hotspot, a Bluetooth connection, or a USB cable. A Wi-Fi hotspot creates a wireless network that other devices can join, a Bluetooth connection pairs the devices and allows data transfer, and a USB cable connects the devices physically and enables data sharing.

A PAN, or personal area network, is a type of network that connects devices within a short range, usually up to 10 meters. A PAN can be used for various purposes, such as transferring files, printing documents, or accessing the internet. A PAN can be created by using Bluetooth, Wi-Fi, or infrared technologies.

A technician can use a PAN to connect a group of users on a field project by using tethering on a mobile device. The technician can activate the tethering service on the mobile device and choose the preferred method of sharing the internet data connection. The other devices can then connect to the mobile device and access the internet through it.

The other options are incorrect because they are not services that can share the internet data connection on a mobile device. Pairing is the process of establishing a connection between two Bluetooth devices, but it does not necessarily share the internet data connection. Bluetooth is a technology that can create a PAN and enable tethering, but it is not a service that can be activated on a mobile device. Hotspot is a term that can refer to a Wi-Fi hotspot created by tethering on a mobile device, but it is not a service that can be activated on its own.

References:

Share a mobile connection by hotspot or tethering on Android

How to share a mobile connection by tethering or hotspot on Android

How to Share Mobile Internet to PC or Other devices