Master the CompTIA A+ Certification Exam: Core 1 220-1101 Exam with Confidence!

The correct answer is D. 5,400rpm HDD.

A 5,400rpm HDD (Hard Disk Drive) is a type of storage device that uses spinning magnetic disks to store data. A 5,400rpm HDD is the least expensive per gigabyte among the options given, as it has a lower rotational speed and performance than other types of HDDs or SSDs (Solid State Drives). A 5,400rpm HDD is suitable for archiving a large number of photos that are not accessed frequently, as it can offer high capacity and reliability at a low cost.

the average cost per gigabyte of a 5,400rpm HDD is around $0.02 to $0.0312, while the average cost per gigabyte of the other options are:

• NVMe SSD: $0.10 to $0.1534
• SCSI RAID: $0.20 to $0.305
• 15,000rpm SAS: $0.30 to $0.40

Therefore, a 5,400rpm HDD is the cheapest option among the four.

The correct answer is C. PoE switch.

A PoE switch is a network device that can provide both data and power to other devices over an Ethernet cable. PoE stands for Power over Ethernet, which is a technology that allows electrical power to be transmitted along with data on twisted pair Ethernet cabling. This eliminates the need for separate power supplies or AC adapters at the users’ desks, as the VoIP devices can receive power from the PoE switch12.

A firewall is a network device that monitors and controls incoming and outgoing network traffic based on predefined security rules. It does not provide power to other devices1.

A power injector is a device that adds electrical power to an Ethernet cable for a single device. It is not suitable for a large number of devices, as it would require one power injector per device1.

A router is a network device that connects multiple networks and forwards data packets between them. It does not provide power to other devices1.

The answer is A. High availability and B. Elasticity.

High availability is the ability of a system to remain operational and accessible with minimal or no downtime, even in the event of failures, disasters, or disruptions. High availability can be achieved by designing a system that has redundancy, fault tolerance, and disaster recovery capabilities. For example, a cloud engineer can design a system that replicates data and resources across multiple regions, zones, or availability domains, and uses load balancing and failover mechanisms to distribute the workload and handle failures gracefully12.

Elasticity is the ability of a system to scale up or down automatically in response to changes in demand or utilization. Elasticity can be achieved by designing a system that can dynamically allocate and deallocate resources based on predefined metrics, policies, or triggers. For example, a cloud engineer can design a system that uses auto-scaling groups, horizontal or vertical scaling strategies, and on-demand or spot instances to optimize the performance and cost of the system32.

By implementing high availability and elasticity, a cloud engineer can ensure that the solution is able to immediately fail over to another region in case of an outage and also scale up in the event of high utilization. These are two important aspects of building reliable and scalable cloud architectures. Therefore, options A and B are the correct answers.

Rapid elasticity would be used by an online retailer to quickly add more web servers during peak sales times. References: CompTIA A+ Certification Exam Guide, Exam 220-1001, Page 405

The best way to clean up the toner that spilled into the printer is to use an ESD-safe vacuum. An ESD-safe vacuum is a special type of vacuum that has a filter that traps toner particles and prevents them from escaping into the air. An ESD-safe vacuum also has a grounding wire that prevents static electricity from building up and damaging the printer’s components. Toner is electrically conductive and can cause short circuits or sparks if it contacts sensitive parts of the printer. Therefore, using an ESD-safe vacuum is the safest and most effective method to remove the toner from the printer.

Other methods, such as a magnetic duster, compressed air, or a damp cloth, are not recommended for cleaning up toner spills. A magnetic duster is a device that uses a magnet to attract toner particles, but it can also damage the printer’s components that rely on magnetism, such as the drum or the fuser. Compressed air can blow the toner around and create a cloud of dust that can be harmful to breathe or contaminate other parts of the printer. A damp cloth can smear the toner and make it harder to remove, as well as cause corrosion or rust on the printer’s metal parts.

References:

• Cleaning up Toner Spills or Leaks Inside the Printer - Xerox Support1
• How to Clean Up Toner Spills - YouTube2
• How to Clean up a Laser Toner Spill - Cartouches Certifiées3

DHCP stands for Dynamic Host Configuration Protocol, which is a protocol that provides quick, automatic, and central management for the distribution of IP addresses within a network1. A DHCP server can assign IP addresses and other network information to devices that request them, such as computers, smartphones, and routers2.

The IP address 169.254.2.2 is an example of an APIPA (Automatic Private IP Addressing) address, which is a special type of IP address that devices use when they cannot obtain a valid IP address from a DHCP server3. APIPA addresses are in the range of 169.254.0.1 to 169.254.255.254, with a subnet mask of 255.255.0.03. Devices that use APIPA addresses can only communicate with other devices on the same local network that also use APIPA addresses3.

The router in the question is assigned the address scope of 192.168.1.254/24, which means it has an IP address of 192.168.1.254 and a subnet mask of 255.255.255.04. This address scope belongs to the private IP address range of 192.168.0.0 to 192.168.255.255, which is commonly used for local networks4. Devices that use private IP addresses can communicate with other devices on the same local network or across different networks through NAT (Network Address Translation)4.

The most likely cause of the technician receiving the IP address 169.254.2.2 is that the DHCP server on the router is not working properly or is not configured correctly3. This could be due to various reasons, such as a misconfigured router, a faulty cable, a firewall blocking DHCP traffic, or an exhausted pool of IP addresses3. As a result, the technician’s device cannot obtain a valid IP address from the DHCP server and resorts to using an APIPA address instead3.

To fix this issue, the technician should check the router settings and make sure that the DHCP server is enabled and has enough available IP addresses to assign to devices2. The technician should also check the physical cabling and make sure it is properly connected and secured2. If the issue persists, the technician should try rebooting the router or resetting it to factory defaults2. Alternatively, the technician could manually assign a static IP address to the device that matches the router’s address scope, such as 192.168.1.x/242.

The MOST efficient next step the technician should complete is to install an updated printer driver on the print server12. The issue of information being garbled and looking like code could be related to a compatibility issue with the new firmware and the existing printer driver1. The printer driver is responsible for converting the print job data into a format that the printer can understand and print2. 

Cross-platform virtualization would be the best solution for running Windows software on a computer running macOS. This involves running a virtual machine (VM) on the macOS computer, which emulates a Windows environment and allows the Windows software to be installed and run within the VM.

Cross-platform virtualization allows a computer running macOS to run Windows software. It involves creating a virtual machine on the macOS computer and installing a Windows operating system on it. References: CompTIA A+ Certification Exam Guide, Ninth Edition, Chapter 1

To fix a Cat 5 cable issue where the cable fails when it is moved around, the technician would need to use an RJ45 connector (option E) and a crimper (option F). The technician can use the crimper to attach a new RJ45 connector to the end of the cable, which should resolve the issue.

An RJ45 connector (option E) is a type of connector commonly used for Ethernet networking. It is an 8-position, 8-contact (8P8C) modular plug and jack that is used to terminate Cat 5 and other types of twisted pair cables. A crimper (option F) is a tool used to attach connectors to the ends of cables. In this case, the technician would use the crimper to attach a new RJ45 connector to the end of the Cat 5 cable.

When a cable fails when it is moved around, it often indicates that there is a problem with the connector at the end of the cable. By attaching a new RJ45 connector using a crimper, the technician can ensure that the cable has a secure and reliable connection.

A network tap is used to intercept the signals passing over a cable and send them to a packet or protocol analyzer. Taps are either powered or unpowered:

The most likely action that would resolve the issue is to clean the keyboard. Sometimes dust, hair, and other debris can affect keyboard functionality. The technician can try to clean the keyboard as much as possible, which may be enough to get the keyboard back in working order

Three beeps indicate a "base memory read/write test error". Check out "beep codes" for more information.

https://en.wikipedia.org/wiki/Power-on_self-test#POST_beep_codes_on_CompTIA_A.2B_certification_exam

Reseating the RAM is the best course of action to remediate the issue of three consecutive beeps during boot, as it may indicate a RAM failure or loose connection. By reseating the RAM, the technician can ensure that the connection is secure and the computer should boot normally. References: CompTIA A+ Certification Exam Objectives 1001, 1.9

The most likely reason that the technician is unable to select the channel with almost no RF pollution is that it is reserved for licensed band use. Some channels are reserved for specific purposes and require a license to use. These licensed bands are typically used for critical infrastructure, public safety, or military operations, and unlicensed devices are not allowed to use them. References: CompTIA A+ Certification Exam Objectives - 220-1001: 3.3 Compare and contrast common networking hardware devices.

When a user connects a smartphone to a laptop, they create a Personal Area Network (PAN). A PAN is a type of network used for communication between devices in close proximity to each other, typically within a range of a few meters or less. This type of network is commonly used for wireless communication between personal devices, such as connecting a smartphone to a laptop for file sharing or internet access. References: CompTIA A+ Certification Exam Objectives - 220-1001: 1.1 Explain common connectors and their uses.

The technician should check the MAC filtering list next as the new router may have a different MAC address than the old router. References: CompTIA A+ Certification Exam Guide, Exam 220-1001, Page 332