Free Checkpoint 156-315.82 Practice Exam with Questions & Answers | Set: 4

The correct answer isD. migrate_server exports thelatest published database revision, not every historical revision and not unpublished SmartConsole session changes. Check Point’s R82 upgrade guidance states clearly that only the latest published database revision is upgraded, and if there are pending changes, the administrator should publish the session first. That directly eliminates option A because unpublished changes are not included. Option B is wrong because all previous revisions are not exported/upgraded. Option C is fabricated; there is no “last three revisions” rule. This is a critical operational point: before an Advanced Upgrade or migration export, all GUI clients should be closed and pending changes should be published if they must be preserved. A saved-but-unpublished SmartConsole session is not the same as a published database revision. (sc1.checkpoint.com)

========

The correct answer isA. IKEv2 establishes the initial tunnel state using two main exchanges:IKE_SA_INITandIKE_AUTH. Each exchange is a request/response pair, so the normal initial exchange uses four messages/packets total. RFC 7296, the IKEv2 specification, states that implementations must support the four-message IKE_SA_INIT and IKE_AUTH exchanges that establish two SAs: one for IKE and one for ESP or AH. This fits Check Point’s IKEv2 behavior because IKEv2 is selected as the VPN community encryption negotiation protocol, while the actual negotiation sequence follows the standard IKEv2 protocol. Option B incorrectly describes the older IKEv1 Main Mode plus Quick Mode style count often remembered as a larger exchange. Option C invents a legacy-peer exception. Option D wrongly assigns four packets to SA_INIT alone. The CCSE distinction is:IKEv1 Main Mode = 6 packets; IKEv2 initial exchange = 4 packets total. Reference topic:IKEv2 Initial Exchanges / IKE_SA_INIT and IKE_AUTH.

The correct answer isC. With Manual NAT rules, the administrator must consider Proxy ARP behavior. Check Point documentation states that if manual NAT rules are used, Proxy ARP entries must be configured so the translated IP address is associated with the MAC address of the Security Gateway interface on the same network as the translated addresses. This is necessary because automatic Proxy ARP generation is tied to automatic NAT behavior; manual NAT scenarios often require explicit Proxy ARP handling. Option A is wrong because the Proxy ARP configuration belongs on the Security Gateway side, not by editing a Management Server file. Option B incorrectly references automatic ARP behavior as the required manual NAT solution. Option D is not a general manual NAT requirement and would be an arbitrary rule-ordering statement. The practical R82 rule is blunt: when you use Manual NAT and expect the gateway to answer ARP for translated addresses, configure Proxy ARP correctly and enable the relevant merge behavior where required. Reference topic:Manual NAT Rules / Proxy ARP for Manual NAT.

========

The correct answer isB. SMO is the ElasticXL management abstraction that lets the cluster be managed as one Security Gateway using one management IP address. It is used for management communication and policy installation, and the SMO Master distributes/updates relevant management tasks to the other members. Option A is badly worded and incorrectly focuses on each member connecting through a server virtual IP. Option C is the opposite of SMO because it says each member gets its own object. Option D is wrong because ElasticXL SMO applies to the scalable Security Gateway cluster, not to a cluster of Management Servers.

========

The correct answer isD. For CCSE R82 and the official R82 ElasticXL documentation, ElasticXL Cluster is anR82 and higherScalable Platforms feature. R82 documentation links ElasticXL requirements to the R82 Release Notes/support matrix and describes ElasticXL Cluster requirements under the R82 Scalable Platforms Administration Guide. Option B is wrong because R82.10 is newer than the minimum. Option C is not supported by the official R82 ElasticXL documentation as the minimum required release for installing ElasticXL Cluster. Option A is also not the correct R82 answer; do not confuse unrelated Jumbo Hotfix support notes with the official ElasticXL supported-release baseline. The clean exam answer isR82.

========

The correct answer isB, with one important precision: in R82, SmartConsole Central Deployment is primarily used for Security Gateways and Cluster Members, and R82 enhancements also add support for package installation onSecondary Management Servers,Dedicated Log Servers, andDedicated SmartEvent Servers. Check Point’s R82 “What’s New” documentation states that Central Software Deployment through SmartConsole was enhanced to support installation of packages on Secondary Management Servers and Dedicated Log Servers. The Security Management Administration Guide also states that Central Deployment can deploy Upgrade Packages on Security Gateways, Cluster Members, Log Servers, and secondary management. Option A is incomplete because it omits Dedicated Log Servers. Option C reflects the older/common gateway-and-cluster focus but is incomplete for R82. Option D is plainly wrong because clusters are supported. The best available answer is thereforeB, but a strict administrator should interpret “Security Management Servers” here as supportedsecondary managementtargets, not a blanket claim that every primary management server upgrade should be driven through Central Deployment. Reference topic:R82 Central Deployment Enhancements / Supported Targets.

The correct answer isA. The fw fetch command is used on a Security Gateway to fetch the Security Policy from a specified host, typically the Security Management Server, and install it into the kernel. The R82 CLI Reference Guide states that fw fetch “fetches the Security Policy from the specified host and installs it to the kernel.” It can fetch policy from a Management Server listed in $FWDIR/conf/masters, from a specified master, or from a local policy directory on the gateway. Option B is not a valid Check Point policy-loading command in this context. Option C is wrong because fw install is not the gateway-side command used to manually fetch and load policy files. Option D is generic and not a valid CLI command for this task. For exam purposes, remember the direction:Management pushes policy during normal install; Gateway manually retrieves policy using fw fetch. Reference topic:R82 CLI Reference Guide / fw fetch.

========