Free Huawei H35-580_V2.0 Practice Exam with Questions & Answers

According to the Huawei Releases 5G Series Products, Huawei’s AAU5313 and AAU5613 are both RF modules that support 64T64R. The AAU5313 is an ultra-wideband Massive MIMO product that supports both 64T64R and 400 MHz bandwidth on the C-band. The AAU5613 is a BladeAAU Pro product that supports 64T A+P integration on sub-3 GHz bands. The AAU5612 is a BladeAAU product that supports only 32T A+P integration on sub-3 GHz bands. The RRU3939 is not an AAU product but an RRU (Remote Radio Unit) product that supports only 8T8R on sub-3 GHz bands.

According to the China’s Approach to Military 5G Networks and Related Military Applications, CU-DU Split of a base station means that the base station’s control plane functions (CU) and user plane functions (DU) are separated, which can improve network flexibility and scalability.

 According to the LTE-NR tight-interworking and the first steps to 5G, in a Huawei base station, QCI2 can only be configured as an MCG (Master Cell Group) bearer. QCI2 is a voice bearer that requires low latency and high reliability. Therefore, it cannot be configured as an SCG (Secondary Cell Group) bearer or a split bearer that may introduce additional delay or packet loss. QCI6, QCI9, and QQ1 can be configured as either MCG bearers, SCG bearers, or split bearers depending on the service requirements and network conditions.

The Rayce ray tracing model is a propagation model that computes propagation paths using 3-D environment geometry 3. It is based on the shooting and bouncing rays (SBR) method, which launches rays from the transmitter and traces their reflections and diffractions until they reach the receiver or are attenuated below a threshold 4. The Rayce ray tracing model offers more accurate path searching, reflection, and diffraction energy calculation for electromagnetic wave propagation than other models, such as empirical models or deterministic models 5. It also offers higher level prediction accuracy, especially for massive MIMO systems that use beamforming techniques 6. The Rayce ray tracing model is not applicable only to C-band, but also to mmWave and other frequency bands 7.

According to the 5G NR Physical Layer Specifications, demodulation reference signals (DMRSs) are required for the following channels/signals in the downlink and uplink:

• Downlink Physical Broadcast Channel (DPBCH)
• Downlink Physical Downlink Control Channel (DPDCCH)
• Downlink Physical Shared Channel (DPOSCH)
• Uplink Physical Random Access Channel (PRACH)
• Uplink Physical Uplink Control Channel (PUCCH)
• Uplink Physical Uplink Shared Channel (PUSCH)

According to the HCIA-5G V2.0 Exam Outline, no response from the UE, insufficient radio resources, and unauthorized UE are cause values of QoS flow setup failures, which correspond to options A, B, and D. Insufficient transmission resources is not a cause value of QoS flow setup failures, but a cause value of handover execution failures, which corresponds to option C.

According to the 5G NR Downlink CSI Reporting, CSI-RS is the channel/signal that is used by the UE to measure and obtain the CQI. CSI-RS stands for Channel State Information Reference Signal, which is a downlink reference signal transmitted by the gNodeB to enable the UE to estimate the channel quality and feedback the CQI to the gNodeB. The CQI is an indicator of how good or bad the channel quality is, and it can be used by the gNodeB to adjust the modulation and coding scheme for data transmission.

According to the Huawei’s Latest AAU Products, Huawei’s AAUs have an operating voltage of -48 V DC and support LTE-NR dual-mode on some frequency bands, such as C-band and sub-3 GHz bands. The article also states that Huawei’s new-generation 64T64R AAUs provide higher coverage gains than conventional 32T32R AAUs by using ELAA (extremely large antenna array) technology. Huawei’s AAUs do not support GSM-NR dual-mode on any frequency band, as GSM is not a compatible RAT with NR.

According to the Career Certification - Huawei Enterprise, single site verification is used to test and verify the equipment functions and coverage capability after gNodeB hardware is installed and commissioned, which corresponds to option C.

According to the HCIA-5G V2.0 Exam Outline, in the NSA DC architecture, when a UE moves to a neighboring gNodeB, the SgNB change procedure is triggered, which corresponds to option D.