Free HP HPE3-U01 Practice Exam with Questions & Answers | Set: 2

In order to allow inter-PC communication in the same broadcast domain, both switches need to have the same VLAN configured on the ports that connect to the PCs and the trunk port that connects to each other. Option B shows the correct configuration for both switches, as follows:

• On Switch-1, interface 0/1 is configured as an access port on VLAN 10, which matches the VLAN of PC-1. Interface 0/2 is configured as a trunk port, which allows VLAN 10 traffic to pass through to Switch-2.
• On Switch-2, interface 0/1 is configured as an access port on VLAN 10, which matches the VLAN of PC-2. Interface 0/2 is also configured as a trunk port, which allows VLAN 10 traffic to pass through from Switch-1.

Option A is incorrect because it does not configure the trunk port on Switch-2, which prevents VLAN 10 traffic from reaching Switch-1. Option C is incorrect because it configures the trunk port on Switch-1 with the wrong encapsulation mode (ISL instead of dot1q), which causes a mismatch with Switch-2. Option D is incorrect because it configures the access ports on Switch-2 with the wrong VLAN (20 instead of 10), which isolates PC-2 from PC-1.

References:

1: Layer 2 VLAN Configuration on a Cisco Switch (with Example) - Networks Training 2: VLAN Configuration Commands Step by Step Explained - Computer Networking Notes 3: How To Configure VLANs On the Catalyst Switches - Cisco Community 4: Configure VLAN on Cisco Switch Using Cisco Packet Tracer - TECHNIG

To convert a hexadecimal number to a binary number, we need to follow these steps:

• Write down the hexadecimal number and assign a power of 16 to each digit, starting from the rightmost with 16^0.
• Convert each hexadecimal digit to its decimal equivalent by multiplying it with its power of 16.
• Add all the decimal values to get the decimal equivalent of the hexadecimal number.
• Divide the decimal number by 2 repeatedly and write down the remainders from bottom to top.
• The binary number is the sequence of remainders obtained in the previous step.

Let’s apply these steps to the hexadecimal number 17:

• 17 = 1 × 16^1 + 7 × 16^0
• 17 = 16 + 7
• 17 = 23 in decimal
• 23 / 2 = 11 with remainder 1
• 11 / 2 = 5 with remainder 1
• 5 / 2 = 2 with remainder 1
• 2 / 2 = 1 with remainder 0
• 1 / 2 = 0 with remainder 1
• The binary number is 10111

Therefore, the binary equivalent of the hexadecimal number 17 is 10111 (option B).

References: The answer can be verified by using the following resources:

• Hexadecimal to Binary Converter - Binary Hex Converters
• How to Convert 17 from hexadecimal to binary - Calculator Online
• Convert hexadecimal number 17 to binary - CoolConversion
• 17 in Binary - How to Convert 17 from Decimal to Binary? - Cuemath

The 051 Model is a reference model that describes how data communications occur on a network using five layers: physical, data link, network, transport, and application. The 051 Model is based on the OSI Model, which has seven layers, but it simplifies the presentation and session layers into the application layer. The 051 Model is used to understand the functions and interactions of different network components, such as devices, protocols, and services. Each layer of the 051 Model has a specific role and responsibility in the data communication process, as follows:

• The physical layer defines the electrical and mechanical characteristics of the transmission medium, such as cables, connectors, and signals. It also determines how data is encoded into bits and transmitted over the medium.
• The data link layer defines the rules and methods for accessing and sharing the transmission medium among multiple devices. It also provides error detection and correction mechanisms to ensure reliable data delivery.
• The network layer defines the logical addressing and routing schemes for data packets across different networks. It also provides congestion control and fragmentation/reassembly functions to optimize network performance.
• The transport layer defines the end-to-end communication and reliability services for data segments between applications. It also provides flow control and multiplexing/demultiplexing functions to manage data streams.
• The application layer defines the protocols and services that enable user applications to exchange data over the network. It also provides functions such as encryption, authentication, and compression to enhance data security and efficiency.

References:

• 051 Model
• OSI Model
• Network Fundamentals

In the 2.4 GHz band, only channels 1, 6, and 11 are non-overlapping, meaning that they do not share any frequency spectrum with each other. This makes them the preferred channels for Wi-Fi networks to minimize interference with other devices that use the same band, such as Bluetooth, microwave ovens, cordless phones, etc. Using non-overlapping channels also allows for better performance and throughput, as devices on the same channel have to contend for the medium and avoid collisions. Channels 2 to 5 overlap with channel 1, channels 7 to 10 overlap with channel 6, and channels 12 and 13 overlap with channel 11. Channel 14 is not allowed in most countries and regions, and it also overlaps with channel 11. Therefore, using any of these channels would cause interference with the non-overlapping channels and degrade the network quality. The 2.4 GHz band has a total of 14 channels, each with a bandwidth of 22 MHz and a center frequency separated by 5 MHz. However, the actual frequency range used by each channel is wider than 22 MHz, as the signal spreads out due to modulation. This means that adjacent channels partially overlap with each other, and only channels that are 25 MHz apart or more are completely non-overlapping. The following table shows the center frequency and frequency range of each channel in the 2.4 GHz band:

Table

Channel

Center frequency (MHz)

Frequency range (MHz)

1

2412

2401-2423

2

2417

2406-2428

3

2422

2411-2433

4

2427

2416-2438

5

2432

2421-2443

6

2437

2426-2448

7

2442

2431-2453

8

2447

2436-2458

9

2452

2441-2463

10

2457

2446-2468

11

2462

2451-2473

12

2467

2456-2478

13

2472

2461-2483

14

2484

2473-2495

As shown in the table, only channels 1, 6, and 11 have a 25 MHz separation between their center frequencies, and therefore do not overlap with each other or any other channel. This makes them the best choice for Wi-Fi communications in the 2.4 GHz band. References:

• Aruba Certified Network Technician (ACNT) | HPE Aruba Networking
• Aruba Documentation Portal
• List of WLAN channels - Wikipedia
• Why Channels 1, 6 and 11? | MetaGeek
• All about WiFi Channels & Frequency Bands – A simple Guide
• WiFi Channels: Complete Guide with Tips to Boost Signal Performance

 A Wi-Fi frame is a unit of data transmission in a wireless network that follows the 802.11 standard. There are three types of Wi-Fi frames: management, control, and data. Management frames are used to establish and maintain the connection between wireless devices, such as access points (APs) and stations (STAs). Control frames are used to coordinate the access to the wireless medium and avoid collisions. Data frames are used to carry the actual information between wireless devices1

A Service Set Identifier (SSID) is a name that identifies a wireless network. A Basic Service Set Identifier (BSSID) is a unique identifier for a wireless access point within a wireless network. A BSSID is usually the MAC address of the wireless interface of the AP. An SSID can be associated with multiple BSSIDs, forming an Extended Service Set (ESS). For example, a wireless network with multiple APs can have the same SSID but different BSSIDs for each AP23

A beacon is a type of management frame that is periodically broadcasted by an AP to announce its presence and provide information about the wireless network, such as the SSID, the BSSID, the supported data rates, the security parameters, and the channel number. A beacon is used by STAs to discover and join a wireless network, as well as to synchronize their clocks with the AP. A beacon is usually sent every 100 milliseconds on a fixed interval45

Therefore, the Wi-Fi frame that announces the SSID to BSSID mapping is the beacon, as it contains both the SSID and the BSSID fields in its frame format. The other options are not correct because:

• An association request is a type of management frame that is sent by a STA to an AP to request to join a wireless network. It contains the SSID of the network that the STA wants to join, but not the BSSID of the AP. The BSSID is specified in the association response frame that is sent by the AP to the STA to accept or reject the request4
• A probe request is a type of management frame that is sent by a STA to scan for available wireless networks. It can contain the SSID of a specific network that the STA wants to join, or it can be blank to request information from all networks. It does not contain the BSSID of any AP. The BSSID is specified in the probe response frame that is sent by the AP to the STA to provide information about the network4
• A network allocation vector (NAV) is not a type of Wi-Fi frame, but a mechanism to avoid collisions in a wireless network. It is a timer that indicates how long the wireless medium will be busy for a transmission. Each Wi-Fi frame contains a duration field that specifies the NAV value for that transmission. The NAV value is updated by the wireless devices based on the duration field of the received frames. A wireless device will not transmit any frame if the NAV value is greater than zero, meaning that the medium is occupied.

References: 1: Wi-Fi Frames: A Brief Intro - Cisco Blogs 2: SSID vs BSSID: What’s the Difference? - Actiontec.com 3: Difference Between BSSID and SSID | Difference Between 4: 802.11Management Frames - Tutorialspoint 5: [Beacon frame - Wikipedia] : [Association Request frame - 802.11 Wireless Networks: The Definitive Guide, 2nd Edition [Book]] : [Probe Request frame - 802.11 Wireless Networks: The Definitive Guide, 2nd Edition [Book]] : [Network Allocation Vector - an overview | ScienceDirect Topics] : [NAV (Network Allocation Vector) - GeeksforGeeks]

The IP address 10.0.128.0/23 is a Class A private address with a subnet mask of 255.255.254.0. This means that the network prefix is 10.0.128.0 and the host identifier is the last 9 bits of the address. To find the number of IP assignable addresses, we need to subtract 2 from the total number of possible hosts, which is29=512. This is because the network address (10.0.128.0) and the broadcast address (10.0.129.255) are reserved and cannot be assigned to any host. Therefore, the number of IP assignable addresses is 512 - 2 = 510.References:IP Subnet Calculator,CIDR Calculator for IPv4 addresses,Free online IPv4 subnet calculator

To convert a binary number to a decimal number, we need to follow these steps:

• Write down the binary number and assign a power of 2 to each digit, starting from the rightmost with 2^0.
• Convert each binary digit to its decimal equivalent by multiplying it with its power of 2.
• Add all the decimal values to get the decimal equivalent of the binary number.

Let’s apply these steps to the binary number 10001010:

• 10001010 = 0 × 2^0 + 1 × 2^1 + 0 × 2^2 + 1 × 2^3 + 0 × 2^4 + 0 × 2^5 + 0 × 2^6 + 1 × 2^7
• 10001010 = 0 + 2 + 0 + 8 + 0 + 0 + 0 + 128
• 10001010 = 138 in decimal

Therefore, the decimal equivalent of the binary number 10001010 is 138 (option A).

References: The answer can be verified by using the following resources:

• Convert 10001010 from binary to decimal - Calculator Online
• How to Convert decimal number 10001010 in binary? - CoolConversion
• 10001010 to decimal - Calculatio
• Binary Code | Binary: 10001010 | Decimal: 138 | Bits: 8

The Institute of Electrical and Electronics Engineers (IEEE) is an organization that develops and publishes international standards for various fields of engineering, including electrical, electronic, computer, software, and telecommunications. IEEE standards are widely used and recognized by the industry, academia, and governments. IEEE standards cover topics such as wireless networking, Ethernet, power systems, smart grid, cybersecurity, robotics, biomedical engineering, and more. IEEE standards are developed by consensus among experts from different sectors and regions, and are reviewed and updated regularly to reflect the latest technologies and best practices. IEEE standards aim to promote innovation, interoperability, safety, reliability, and efficiency in engineering applications. References: IEEE Standards Association, IEEE - Wikipedia, IEEE Standards - Creative Safety Supply