Free Cisco 600-660 Practice Exam with Questions & Answers

Name: How to Pass 600-660 Exams
Brand: Examstrack
SKU: 600-660
Price: 46 USD
Availability: InStock

Questions 1

A leaf receives unicast traffic that is destined to an unknown source, and spine proxy is enabled in the corresponding bridge domain. Drag and drop the Cisco ACI forwarding operations from the left into the order the operation occurs on the right.

600-660 Question 1

Options:

Cisco 600-660 Premium Access

Daniel

27-Jun-2025

examstrack's 600-660 materials are the key to my guaranteed success. Actual tests were a walk in the park.

Questions 2

Refer to the exhibit.

600-660 Question 2

How is the ARP request from VM1 forwarded when VM2 is not learned in the Cisco ACI fabric?

Options:

Leaf 101 forwards the ARP request to one of the proxy VTEP spines.

POD1 spine responds to the ARP request after the POD1 COOP is updated with the VM2 location.

Leaf 101 encapsulates the ARP request into a multicast packet that is destined to 225.0.37.192.

Leaf 101 switch consumers the ARP reply of VM2 to update the local endpoint table.

Questions 3

An organization migrates its virtualized servers from a legacy environment to Cisco ACI. VM1 is incorrectly attached to PortGroup IT|3TierApp|Web.

600-660 Question 3

Which action limits IP address learning in BD1?

Options:

Enable Enforce Subnet Check

Enable Rouge Endpoint Control

Enable GARP-based EP Move Detection Mode

Disable Remote EP Learn

Questions 4

Which two actions are the Cisco best practices to configure NIC teaming load balancing for Cisco UCS B- Series blades that are connected to the Cisco ACI leaf switches? (Choose two.)

Options:

Create vPC+

Enable LACP active mode

Create PAgP

Create vPC

Enable MAC pinning

Questions 5

Refer to the exhibit.

600-660 Question 5

An engineer extends a Cisco ACI Multi-Pod setup to a Cisco ACI Multi-Site implementation. Which action allows the interconnection?

Options:

Configure BIDIR-PIM in the IPN and ISN

Use dedicated uplinks on Site 1 spines for ISN connections

Connect all spines to the IPN and ISN

Filter the advertisement of the Site 2 TEP pool into the IPN

Questions 6

Refer to the exhibit.

600-660 Question 6

Which two configuration steps are required in ISN for Cisco ACI Multi-Site setup? (Choose two.)

Options:

Connect Spine2 to ISN routers.

Configure BIDIR-PIM throughout the ISN

Increase ISN MTU to support the maximum MTU that is sent by endpoints

Configure OSPF between spines and ISN routers

Enable IGMPv3 on ISN routers

Questions 7

Refer to the exhibit.

600-660 Question 7

A customer implements Cisco ACI Multi-Site with default MTU settings between two sites. Which configuration should be applied on the interface Eth1/10 on the ISN-1 device?

600-660 Question 7

Options:

Option A

Option B

Option C

Option D

Questions 8

What is a use of the Overlay Multicast TEP in Cisco ACI Multi-Site communication?

Options:

to perform headend replication

to act as the source IP for BUM traffic

to establish MP-BGP adjacencies with remote spines

to send and receive unicast VXLAN data plane traffic

Questions 9

An engineer configures a new Cisco ACI Multi-Pod and must set up the link between the spine and the IPN device. Which three actions should be taken to accomplish this goal? (Choose three.)

Options:

Enable MP-BGP routing

Enable BIDIR-PIM protocol

Enable PIM-SM protocol

Enable OSPF routing

Enable IS-IS routing

Enable DHCP relay

Questions 10

Refer to the exhibit.

600-660 Question 10

A network engineer configures a Layer 4 to Layer 7 device for an outside routed firewall that is connected to POD-1 inside a Cisco ACI fabric that consists of two pods. All traffic from POD-1 or POD-2 that uses the L3Out should pass through the routed firewall. Which Function Type must be implemented in the service graph for POD-2 to use L3Out?

Options:

GoThrough

GoTo