Free CompTIA N10-009 Practice Exam with Questions & Answers | Set: 4

Quality of Service (QoS)is the best cost-effective solution. It prioritizes traffic based on application criticality. If the bandwidth is limited and only a few users are affected, prioritizing that application traffic can improve performance without needing costly bandwidth upgrades or direct connections.

The failure of a ping to 127.0.0.1 (the loopback address) indicates a problem with the workstation’s TCP/IP stack or network interface card (NIC). Since 127.0.0.1 is a local address, the issue is not related to the network, router, or DNS. The first step in diagnosing this issue is to verify the NIC interface status to ensure the network adapter is functioning and properly configured.

Why not Verify the network is not congested? Network congestion affects external connectivity, not the loopback address.

Why not Verify the router is not dropping packets? Router issues are irrelevant since the loopback ping fails locally.

Why not Verify that DNS is resolving correctly? DNS resolution is not involved in pinging 127.0.0.1, which uses a direct IP address.

Packet loss occurs when network packets fail to reach their destination, leading to disruptions in connectivity and performance issues. In this scenario:

Users report connectivity issues and lag during video meetings.

The administrator detects increased retransmissions in tcpdump, which is a strong indicator of lost packets that must be resent.

Video meetings are particularly sensitive to packet loss, leading to buffering, frozen screens, and dropped calls.

Latency (Option A) refers to delayed data transmission but does not necessarily cause retransmissions.

Bottlenecking (Option C) happens when a network component (e.g., router, switch) cannot handle the traffic load, but packet retransmissions are more directly related to packet loss.

Jitter (Option D) affects the consistency of packet arrival times, but the symptoms described here are more aligned with packet loss rather than timing variations.

? Reference: CompTIA Network+ (N10-009) Official Study Guide – Section: Troubleshooting Connectivity Issues

GDPR (General Data Protection Regulation)is alegal frameworkenforced by the European Union to protect personal data and privacy. Unlike internal organizational policies such as AUPs or codes of conduct, GDPR is alegislated regulation, and organizations must comply or face legal consequences.

Introduction to Subinterfaces:

Subinterfaces are logical interfaces created on a single physical interface. They are used to enable a router to support multiple networks on a single physical interface.

Use Case for Subinterfaces:

Subinterfaces are commonly used in scenarios where VLANs are implemented. A router with a single physical LAN port can be configured with multiple subinterfaces, each associated with a different VLAN.

This setup allows the router to route traffic between different VLANs.

Example Configuration:

Consider a router with a single physical interface GigabitEthernet0/0 and two VLANs, 10 and 20.

interface GigabitEthernet0/0.10

encapsulation dot1Q 10

ip address 192.168.10.1 255.255.255.0

!

interface GigabitEthernet0/0.20

encapsulation dot1Q 20

ip address 192.168.20.1 255.255.255.0

The encapsulation dot1Q command specifies the VLAN ID.

Explanation of the Options:

A. A router with only one available LAN port: This is correct. Subinterfaces allow a single physical interface to manage multiple networks, making it essential for routers with limited physical interfaces.

B. A firewall performing deep packet inspection: Firewalls can use subinterfaces, but it is not a requirement for deep packet inspection.

C. A hub utilizing jumbo frames: Hubs do not use subinterfaces as they operate at Layer 1 and do not manage IP addressing.

D. A switch using Spanning Tree Protocol: STP is a protocol for preventing loops in a network and does not require subinterfaces.

Conclusion:

Subinterfaces provide a practical solution for routing between multiple VLANs on a router with limited physical interfaces. They allow network administrators to optimize the use of available hardware resources efficiently.

A misaligned parabolic antenna can cause a significant increase in input errors because the signal is not properly focused or directed towards the receiving antenna, resulting in poor reception and data corruption. The document confirms:

“Misalignment of parabolic microwave antennas can lead to weak or incorrect signal reception, causing an increase in input errors and connectivity issues on the link.”

A /23 subnet provides 512 total addresses, of which 510 are usable (subtracting 2 for network and broadcast addresses). This would satisfy the need for 255 additional addresses.

•A. Isolate smart devices to their own network segment: Network segmentation using VLANs or separate SSIDs ensures that smart devices (like speakers) are not on the same network as guests, preventing unauthorized control.

•E. Change the default credentials: Many IoT devices (e.g., smart speakers) come with default usernames and passwords. If these are not changed, unauthorized users can easily take control.

•Why not the other options?

•B. Configure IPS: IPS (Intrusion Prevention System) detects threats but cannot block specific guest actions on an IoT device.

•C. Install a new AP: A new access point does not solve the unauthorized control issue.

•D. Set up a syslog server: Helps with logging, but does not prevent unauthorized access.

•F. Configure GRE: Generic Routing Encapsulation (GRE) is used for VPN tunneling, which is irrelevant in this case.

If a ping to 10.0.100.19 is unreachable, the most likely issue is that users are on the wrong subnet and cannot communicate with the server.

Breakdown of Options:

A. The users are on the wrong subnet. ✅ Correct answer. If users are on a different subnet without proper routing, they won't reach the server.

B. The DHCP server renewed the lease. – Would change the client’s IP, but the server’s static IP should remain unchanged.

C. The IP address was not reserved. – DHCP reservations matter for dynamic IPs, but RDP servers typically have static IPs.

D. The hostname was changed. – Would affect DNS resolution, but pinging the IP directly would still work.